Gear Hunter
Traynor - AMCUSTOM
Description
Acoustic Master Series Characteristics
Effective simplicity and precise reproduction are two of the design criteria Yorkville Sound set for this new line of Traynor Acoustic Master amplifiers. Acoustic-electric guitarists and others will be pleased at the neutral response available with minimal control adjustments. Active filtering circuits allow effective tonal shaping with fewer knobs and switches so you get the sound you want quickly, easily and without feedback.
Inside, high-grade glass epoxy circuit boards, low-noise metal film resistors and jacks with gold plated contacts ensure quiet, reliable performance onstage or in-studio. Outside, you will find heavy-gauge metal speaker grilles, rugged plywood construction and distinctive Buggy Whip leatherette covering.
AM Custom Details:
Flagship of the Acoustic Master line, the AM Custom is an advanced, 3-channel mixer/amplifier/monitor designed to precisely reproduce acoustic guitar or other acoustic instruments, also vocals and line-level music sources and all in stereo. A total of 225 watts of clean power is distributed to a long-excursion, 8-inch woofer and dual neodymium dome tweeters mounted on an angled internal speaker baffle for enhanced sound distribution and stereo separation.
Features also include 1/4-inch/XLR "combi" mic/line inputs with 48v Phantom power available for condenser mics on channels 2 & 3 (it does not affect dynamic mics, instruments or line inputs if you opt for them),also insert jacks for patching outboard effects, EQ, etc. into specific channels, 4-band channel EQ's with frequency-tuneable Notch filters to control feedback, dual independent 24-bit Onboard digital Effects processors with Footswitch bypasses, an Auxilliary 1/4" input with its own Gain control for connecting a PA or recording desk monitor feed, RCA auxiliary inputs for a CD or MP3 player and a choice of pre- and post-EQ balanced Line Outputs with a Ground Lift button to defeat loop hum.
Note: model TB1 tilt-back legs available as an accessory.
Specifications:
* Type - Stereo Mixer/Amp/Monitor
* Total Cont. Power (Watts) - 225
* Total Burst Power, 2 cycle (Watts) - 250
* Bi-Amp Power (Cont.Watts) - 150/woofer, 25 each/tweeters
* Speaker Complement - 8-inch 150 watt deep-excursion woofer, 2 X 1-inch Neodymium Dome Tweeters
* Crossover - active @ 2.5kHz
* Frequency Response (Hz +/-3dB) - 50-20k
* Hum and Noise - -98dB
* Channel 1 Input - 1/4-inch unbalanced, 1 meg-Ohm
* Channel 1 Controls - Gain, 4 band EQ +/-15dB @ 75, 300, 1k & 7kHz, Notch -24dB steep-slope with frequency sweepable from 80 to 1kHz w/Off position, Effects Select, Modify and Mix
* Channel 1 Insert - 1/4" TRS (Tip=send, Ring=return)
* Channel 1 LED - Clip
* Channel 2 Input - 1/4"/XLR "combi" jack with 48V Phantom power available (does not affect dynamic mics, instruments or line inputs)
* Channel 2 Controls - Gain, EQ +/-15dB @ 75, 300, 1k & 7kHz, Notch -24dB steep-slope with frequency sweepable from 80 to 1kHz w/Off position, Effects Active/Defeat * switch (Ch.2 shares the Ch.1 Efx processor)
* Channel 2 Insert - 1/4" TRS (Tip=send, Ring=return)
* Channel 2 LED - Clip
* Channel 3 Input - 1/4"/XLR "combi" jack with 48V Phantom power available (does not affect dynamic mics, instruments or line inputs)
* Channel 3 Controls - Gain, EQ +/-15dB @ 75, 300, 1k & 7kHz, Notch -24dB steep-slope with frequency sweepable from 80 to 1kHz w/Off position, Effects Select, Modify and Mix
* Channel 3 Insert - 1/4" TRS (Tip=send, Ring=return)
* Channel 3 LED - Clip
* Aux. 1/4-Inch Input - bypasses the Line Outs to eliminate gain loops when used as a monitor feed input. Also accepts instrument inputs.
* Aux. Gain - feeds the 1/4" Aux input signals directly to the power amplifer section & is not affected by the Master volume
* Aux. RCA Inputs - pre Master Volume
* Master Volume - Controls all levels except 1/4" Aux.
* Input Sensitivities - ch1,2,3 & Aux = 100mV
* Line Outs - 1/4-inch = post-EFX, XLR = Pre-EFX
* Line Out Level (incl. Insert send) - 1Vrms
* Insert Return Sensitivity - 0.5Vrms
* Effects Processors - 24-bit digital w/16 presets
* Effects Controls - Select, Modify & Mix
* Effects Footswitch - takes a 2-button switch (eg, Apex AFS2) and bypasses channel 1/2 and channel 3 processors independently
* Protection - Insert Return Limiter, Clip Limiter
* Cabinet Construction - 17mm muli-ply
* Dimensions (DWH, inches) - 12.5 x 20 x 13
* Dimensions (DWH, cm) - 50.8 x 32 x 33
* Weight (lbs / kg) - 35 / 15.9
